Deliver to KSA

For best experience Get the App

SiglentTechnologies SDS1052DL+ 50 MHz Digital Storage Oscilloscope

SiglentTechnologies SDS1052DL+ 50 MHz Digital Storage Oscilloscope

Q: What probes can I use with this scope that will allow me to look at 50 microvolt signals between 500 Hz and 30 MHz?

If you have a known gain amplifier that will work at 50 uV and at least show up on your lowest vert. input setting it should work OK for you. I've used this technique. You would use a x-1 probe. A rough measurement on a calibrated receiver would be an S-9 reading on its S-meter.

Q: Could I use this scope with included probes to check 110/220v AC waveform output of inverters cleanness for spikes or transients etc?

You can, but you have to be very careful of three things: First, you are, of course, working with lethal voltages, hence caution is advised. If you don't know the proper precautions, ask an electrician. Second, for the protection of the scope and the probe, you might want to make an outboard voltage divider - Say 91K(@1W), in series with 9.1K (@1/4W). Hot side of 110V goes to high end of 91K, you put the probe at the juncture with 9.1K, and the other end of 9.1K goes to ground, scope lead, and neutral. Your voltages will read 1/10 of actual. For your purposes, the accuracy presumably is not important. (If it is, use 1% resistors and calibrate.) Third, and most important: As a rule in residential power systems, the 220 feed consists of two hot leads, derived from a center-tapped transformer. The center tap is the neutral and grounded at the main fuse panel. Do NOT connect the probe ground to anything but the neutral. You could be in for a world of hurt. (If you want to look at both sides of the 220 at the same time, you can: make another voltage divider, use it on channel 2. Then if you do the math function CH1+CH2, you'll see the combined waveform.) BTW, the waveform you get is likely to vary with the type and amount of load you put on the inverter.

Q: can you change the resolution of the picture save to usb feature?

I don't think you can change the screen resolution (480x234 pixels). You can record a waveform for a length of time and save that recorded waveform to the USB device. You can also save recorded waveforms as csv (comma separated values) files to import into a spreadsheet. Hope this helps.

Q: Does this come with a Calibration Certificate?

My unit just had QC stamps. As far as calibration it is spot on when I feed it from either an RF or audio generator. The frequency counter is within 100 Hz at 100 MHz as compared to my HP 5316 counter.

4.1/5

Product ID: 32236976

Secure Transaction

12 interest-free installments with tabby

📈Higher resolution display

📊Built-in frequency counter

🔌USB & LAN interfaces

Frequently Bought Together

Siglent Technologies SDS1052DL+ 50 MHz Digital Storage Oscilloscope

Micsoa Oscilloscope Probes - BNC to Alligator Clips, Mini Test Clips & BNC Cables (3 Pack)

Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-Channel Arbitrary Waveform Function Generator Frequency Meter 200MSa/s (15MHz)

Description

🔍 Unleash the Power of Precision!

MATH MADE EASY - Perform complex calculations effortlessly with integrated math functions.
SMART MEASUREMENTS - Utilize automatic measurements and built-in cursors for quick analysis.
CONNECT COLLABORATE - Seamlessly integrate with USB and LAN interfaces for enhanced connectivity.
VISUAL CLARITY REDEFINED - Enjoy a new, higher resolution display that brings your measurements to life.
PRECISION MEETS PERFORMANCE - Experience advanced triggers for isolating specific signals with ease.

The Siglent Technologies SDS1052DL+ is a cutting-edge 50 MHz Digital Storage Oscilloscope designed for professionals seeking high performance and versatility. With features like USB and LAN connectivity, advanced triggering capabilities, and a high-resolution display, this oscilloscope is perfect for detailed signal analysis and measurement.

Have a Question? See What Others Asked

What probes can I use with this scope that will allow me to look at 50 microvolt signals between 500 Hz and 30 MHz?

Could I use this scope with included probes to check 110/220v AC waveform output of inverters cleanness for spikes or transients etc?

can you change the resolution of the picture save to usb feature?

Does this come with a Calibration Certificate?

Common Questions

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Pooja R.

The customer service exceeded my expectations. Perfect for buying products you can't find elsewhere.

1 week ago

Sneha T.

Received my product in pristine condition. Great service overall.

1 month ago

View all Trustpilot reviews

Shop Global, Save with Desertcart

Value for Money

Competitive prices on a vast range of products

Shop Globally

Serving over 300 million shoppers across more than 200 countries

Enhanced Protection

Trusted payment options loved by worldwide shoppers

Customer Assurance

Trusted payment options loved by worldwide shoppers.

Desertcart App

Shop on the go, anytime, anywhere.

SAR 2051

Duties & taxes incl.

KSAstore

Free Returns

30 daysfor PRO membership users

15 dayswithout membership

Secure Transaction

12 interest-free installments with tabby

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Suresh K.

Very impressed with the quality and fast delivery. Will shop here again.

4 days ago

Ayesha M.

The product exactly matches the description. Very satisfied with my purchase.

5 days ago

View all Trustpilot reviews

About Us

Customer Services

Customer Support

Regional Access

Legal & Policies

Social

Get the App

Point your camera to download the app

Customer support

We're available 24/7 to help you!