Nilight - NI -WA 06 LED Light Bar Wiring Harness Kit - 2 Leads 12V On Off Switch Power Relay Blade Fuse for Off Road Lights Work Light, 2 Years Warranty,Black

Bought 2 double light harnesses to install a set of Roadshock Edge 4's on my Jeep JK Rubicon. Used a set of led anti flicker boxes for headlights to connect the flood/low beams to the factory fog light wiring, and the other harness to connect the spot/high beams to the factory high beam circuit. This allowed me to not add any extra switches, but instead use the factory fog switch for low beams, and the high beams come on with the brights. Worked great.

Install was simple, will update on reliability down the road. Harness was long enough for fog lights install on 2000 Silverado so it should be the same for any 99-06 GMT800 truck/SUV. Installed with factory pigtails onto the provided connectors. Switch cables were plenty long enough to reach factory switch location on dash. If you want to run ACC power instead of constant, you’ll need to tap the + into the fuse box. wire loom seems good enough but I still covered it in 3/8 standard wire loom just in case, I also put heat shrink over the connectors, cheap insurance. Great product, will purchase again if this one holds up.

well made , came with connectors for the lights to attach to the harness. Pretty much plug/play.

For years, when adding an accessory to my truck or ATV, I always had to purchase two rolls of automotive wiring, all of the fittings, and then run the wiring to and from the switch, and to and from the accessory. I knew I should’ve used a fuse and/or relay on some of these installs - but I didn’t have the patience to determine which one I needed and how to wire it up.I initially received this harness with the Nilight 12 inch lightbar for my atv and was very impressed with the quality of wire, loom, and connections. All I had to do was lay the wire in, make connections, clean up/secure the wiring, and I was done. It turned an hour of wiring into five minutes.I recently put rock lights on my ATV, and when it didn't come with a wiring harness, I found I could purchase just the harness from Nilight. It was just as easy as it was the last time.The only reservations I have for this harness, is a friend of mine used this same harness on his ATV and as we were riding the wiring melted and started smoking. Luckily he disconnected before it caught fire. His install was correct, and his wires weren’t pinched. So just something to keep in mind.

Good harness. Great price. Works as it should. This is probably my 5th harness I've ordered from this company. Zero complaints.

Great item and easy to read directions

2024-08-28=========It's been under ten bucks lately, so for that price - it's pretty good. I can't speak to the quality of the relay (the main wear item) as I just installed it (and I ordered a second one), but other than that it seems pretty solid. The wires from the relay to the lights are too long, and the ones to the switch are too short, so even on a compact car, I had to extend them (16 ga). The connectors to the lights are just wire spade crimp connectors with small plastic shrouds (provided), which isn't so great for something that will be enduring the worst environmental conditions, so I had to protect them with electrical tape (shrink tubing would have been better, but I didn't bother).I needed to add two sets of auxiliary lights on my Impreza (wide and spot), and I wasn't about to run two sets of wires around the engine (the firewall's entry point in on the opposite side from the battery and the driver position), and given that there is no necessity for running six wires for two switches, I decide to make some changes to the wiring. You only need the white one, the others are just ground and, it should be, switchable +12V (not always-hot); you can get those from the inside fuse panel. For that purpose, I needed to come up with a schematic of the harness, so I'm attaching what I believe is accurate.Generally, there are better ones, but this one should be good enough, if you know your way around electrical connections.

Very good quality , very well made perfect fit , everything you need is in the box. No instructions needed !!!