ELEGRP Lighted Straight Blade Electrical Plug and Connector Set 15 Amp 125 Volt NEMA 5-15P NEMA 5-15R 2 Pole 3 Wire Grounding, Commercial Grade, Yellow, 5 Set

Simple to wire and lights up when plugged in. Doubles as a night light.

Found they work as advertised..But here is another use...plug into any source to see if it has power.this without a cord. one day looking for line tester could not find then i remembered these light up!

I use these to replace worn out sockets. The lighted end is a good safety feature. These are much sturdier than what comes on most extensions and they're a better price than the local stores.

My head snapped 90* when I was walking past one of these units at my local Lowe's hardware and I bought one on a whim. I installed it once home and was impressed by the quality of the unit, the LED light's brightness and the ease by which it installed. There ARE cords that already come with these but usually cost a premium and these allow you to upgrade your current lines.So I ordered two more from Amazon and upgraded my remaining cords used when camping or working in the yard. They're a great little troubleshooter when/if someone unplugs your line from a camper area or someone trips over a line when working in the yard.

nice product

It is the same lighted plug I need for my cord.

I write this to minimize the poor reviews - there are no directions with product but the following should assist . #1-use a new /undamaged or unworn phillips driver - consider a 6-in1 combination driver (cheap) . #2-when separating the 2halves , back out screws a 1/4 turn each & repeat - takes more time but minimizes pressure on crews & threads . #3 ALWAYS keep DIRECT /straight '' perpendicular '' pressure on connection (screw head&driver tip when loosening or tightening-remember the " 1/4 turn then move to next screw & repeat !" #4 Strip outer insulation / casing back 1 1/8'' & slide the base half onto the cord ( don't tighten to cord yet ). #5 strip each wire insulation 1/2'' , twist wire strands with fingers as you slide finger tips off ends - this will aline any loose strands . #6 Check that all 3 screw heads are backed off & entry holes are open completely - these holes are NOT spaced equally apart from each other ! #7 Gently slide one wire into correct hole (they are color coded)making sure 1/16" of wire insulation enters each hole before tightening (even pressure turn driver slowly - do not over tighten ) , do same for remaining two wires . #8 Slide base onto the half you just connected wires to .These 3 screws are NOT spaced equally so aline screws BEFORE tightening screws !! - these screws have threads that are much further apart than any other screws on this product , DO NOT TIGHTEN MORE THAN 1/4 TURN EACH UNTIL ALL 3 HAVE BEEN TIGHTENED ! ! #9 The outer cord casing/insulation should extend just beyond the 3 clamp bars so that they do not contact the 3 wires - important !! If outer casing does not extend beyond these 3 bars , the wire insulation may become damaged/cut .You will need to go back to step #7 & shorten the wires 1/8'' - You may be able to push wire in 1/16'' to avoid shortening wires ? #10 Tighten both screws ( 1/4 turn each until tight ) that result in clamping cord to new cord end .I have use these on 2 separate 100 ' cords both are 12 - 3 . Both pairs of cord ends worked perfectly , no problems , no damage to screw heads , both have bright green illuminated ends the plugged in .Key points - Use New or Unworn tools ! Keep driver **perpendicular** to screw heads !! Turn SLOWLY , 1/4 turns then move to next screw & repeat .Glad to have purchased the 5 pack , highly recommend .

Product was as advertised, have been easy to install & functional as needed!Thank You !